Emerson FM-3 Manuale di Installazione Pagina 43
- Pagina / 230
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
29
Setting Up Parameters
Master Velocity
This displays the velocity of the master encoder in master units/second.
Torque Group
Torque Command
This displays the torque command value before it is limited. The torque command may be
limited by either the Torque Limit (if the Torque Limit Enable destination is active) or current
foldback. Units for this parameter are defined in the Torque Group on the User Units View.
Limited Torque
This is the actual torque commanded to the motor. This value is the result after the
TorqueCommand is limited by the current foldback or the TorqueLimit value (if enabled).
Foldback RMS
This parameter accurately models the thermal heating and cooling of the drive and motor.
When it reaches 100 percent, current foldback will be activated. See the Diagnostics section
for an explanation of foldback.
Shunt Power RMS
This parameter models the thermal heating and cooling of the drive internal shunt. This
parameter indicates the percent of shunt capacity utilization. When this value reaches 100
percent, the drive will generate an RMS Shunt Power Fault. This parameter is not applicable
to the EN-204 which does not have an internal shunt resistor. This parameter is applicable to
the EN-208 and EN-214.
- Reference Manual 3
- Customer Service 5
- Document Conventions 7
- Safety Instructions 8
- Reference Materials 8
- Safety Considerations 9
- Table of Contents 11
- Specifications 189 13
- Glossary 205 13
- Index 213 13
- Introduction 15
- Programming Module 16
- Operational Overview 17
- Keypad Interface 18
- How Motion Works 20
- How Jogging Works 20
- How Home Works 21
- Home Sequence 22
- Accuracy and Repeatability 24
- 1600 µsec 25
- Sensor Min 25
- Calculated 26
- Home Offset 26
- Specified 27
- Home Examples 28
- (2.0 Revs) 29
- Offset Move 29
- Velocity 31
- Acceleration 31
- Deceleration 31
- Run at Velocity 31
- Absolute vs. Incremental 32
- Absolute Index 33
- Incremental Indexes 34
- How Communications Work 36
- Setting Up Parameters 39
- Configuration Group 40
- Drive Encoder Output Group 40
- Positive Direction Group 41
- Motor Position Group 41
- Drive Information Group 42
- Motor Velocity Group 42
- Module Information Group 42
- Master Feedback Group 42
- Torque Group 43
- Scaling 45
- Velocity Group 46
- Acceleration Group 47
- Master Position Setup Group 49
- Master Distance Units 49
- Decimal Places 50
- Master Velocity Units 50
- Master Acceleration Units 50
- Limits Group 52
- Rotary Group 53
- Online Tab 54
- Online Tab (not shown) 56
- Assignments Tab (shown) 56
- Ramps Group 58
- Assignments Tab 58
- Online Status Tab 60
- Tuning Group 62
- Position Error Integral Group 62
- Time Constant 63
- Faults View 64
- PLS View 65
- On Point 66
- Off Point 66
- Direction 66
- Rotary Enable 67
- Rollover Point 67
- I/O Setup Group 68
- Selector View 68
- Assignments 70
- Assignments View 71
- Creating An Assignment: 72
- Deleting An Assignment 72
- Assignment Polarity 73
- Input Lines View 74
- Output Lines View 75
- Motion Group 76
- Jog View 76
- Jog Number 77
- Jog Name 77
- Time Base 77
- Jog Velocity 77
- Jog Acceleration 77
- Jog Sources and Destinations 78
- Home View 82
- Limit Distance 84
- End of Home Position 84
- Home Sources and Destinations 85
- Index View 86
- Enable Index PLS 88
- PLS On Point 88
- PLS Off Point 88
- Registration Parameters 89
- Destinations 91
- Index.#.Sensor Trigger 92
- Network Group 93
- Modbus View 93
- Wait For InPosn 95
- Jog.PlusInitiate 97
- Program Flow Instructions 99
- Index.1.Vel = 20.0 104
- ModuleOutput.1 = ON 104
- Example Programs 105
- ‘Dist=50.000,Vel=1.000in/in 106
- Flying Cutoff/Shear 107
- Programming 109
- Sequence Learn and Playback 110
- Playback Program (Program 2) 112
- Parameter Descriptions 113
- Parameters Saved to NVM 141
- Installation 143
- Modbus Communications 144
- Software Installation 145
- PC System Configuration 145
- Installing PowerTools FM-3 145
- Starting the Software 146
- Accessing Help 147
- Quick Start 149
- User Units View 150
- Master Units View 151
- Position View 151
- Velocity View 152
- Ramps View 153
- Torque View 153
- Tuning View 153
- Step 3: Making Assignments 154
- Click and Hold 155
- Jog Setup 156
- Home Setup 157
- Index Setup 158
- Step 5: Creating a Program 160
- Example Application Start Up 163
- Software Travel Limits 163
- Home Prox 163
- Making Assignments 164
- Tuning Procedures 171
- Tuning Procedure 172
- General Tuning Hints 173
- Tuning Parameters 174
- Response 175
- Feedforwards 175
- Low Pass Filter Group 176
- Line Voltage 176
- Initial Test Settings 177
- Determining Friction 178
- RPM - RPM 179
- FV )100(= 179
- Ramp Units Conversion 181
- Diagnostic Display 183
- Fault Codes 184
- Fault Descriptions 186
- Brake Operation 190
- Analog Outputs 191
- Channel #2 192
- Channel #1 192
- Analog GND 192
- Drive Faults 194
- Error Messages 194
- Programming Error Messages 196
- Online Status Indicators 201
- Specifications 203
- Cable Diagrams 205
- SNCE-XXX Cable 206
- SNCDD-001.5 Cable 206
- SNCO-003 Cable 207
- SNCI-003 Cable 207
- SNCLI-003 Cable 208
- CMDX-XXX Cable 209
- CMDO-XXX Cable 210
- CDRO-XXX Cable 211
- TIA-XXX Cable 212
- DDS-XXX Cable 212
- TERM-H (Head) Terminator 213
- TERM-T (Tail) Terminator 213
- CMDS-XXX Cable 214
- CMMS-XXX Cable 214
- CFCS-XXX Cable 215
- CFCO-XXX Cable 216
- CFOS-XXX Cable 217
- Vendor Contact Information 218
- Glossary 219
Prodotti e manuali riguardandi Networking Emerson FM-3
Networking Emerson Liebert CW Manuale Utente
(88 pagine)
(88 pagine)
Networking Emerson FM-3 Manuale di Installazione
(60 pagine)
(60 pagine)
Networking Emerson 1420 Manuale Utente
(12 pagine)
(12 pagine)
Networking Emerson Liebert FPC Manuale Utente
(16 pagine)
(16 pagine)
Networking Emerson Liebert FPC Manuale Utente
(44 pagine)
(44 pagine)
Networking Emerson X-web300 Manuale Utente
(102 pagine)
(102 pagine)
Networking Emerson OpenComms-485 Manuale Utente
(42 pagine)
(42 pagine)
Networking Emerson X-web500 Manuale Utente
(118 pagine)
(118 pagine)
Candy GO 1462D__1-36S manuály
Uživatelské manuály a uživatelské příručky pro Podložky Candy GO 1462D__1-36S.
Poskytujeme 1 manuály pdf Candy GO 1462D__1-36S ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale