Emerson 1410 Manuale di Servizio Scaricare il pdf (Pagina 80)

Configuring and Operating the System

AXP 1410 Installation and Use (6806800H70D)

5.2.1 Default VLAN Configuration

The AXP 1410 system provides four network planes. They are, base network a and b and fabric

network a and b. The following figures show the VLAN configuration.

Figure 5-1 Switch Management Fabric Interface Bridge Configuration

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 221 222

AXP 1410 1
Trademarks 2
Contact Address 2
Contents 3
List of Tables 10
List of Figures 13
About this Manual 15
Abbreviations 16
Conventions 19
Summary of Changes 20
Comments and Suggestions 21
System Overview 23
1.1.1 Shelf 26
1.1.2 Backplane 26
1.1.3 Shelf Manager 26
1.1.4 Blades 27
1.1.5 Hub Slots 28
1.1.6 Rear Transition Modules 28
1.1.7 Power Entry Modules 28
1.1.8 Fan Tray Modules 28
1.2 Standard Compliances 29
1.3 Ordering Information 30
1.4 Product Identification 32
Site Preparation 35
2.3 Requirements 37
2.3.2 Power Requirements 39
2.4 Dimensions and Weight 40
2.5 Mounting Options 41
2.6 Cooling Considerations 42
2.7 Acoustic Noise Control 44
3.3 Installation 46
3.3.2 Connecting the Cables 51
3.3.2.1 DC Power Cable 52
3.3.3 Grounding the System 56
3.3.4 Powering Up the System 57
3.4 Powering Down the System 58
3.5 Emergency Power Off 58
FRU Installation 61
4.2.1 Installing the Board 63
4.2.2 Removing the Board 64
4.3.1 Tools You Will Need 65
4.3.2 Removing the PEM 65
4.3.3 Installing the PEM 68
4.4.1 Removing the Upper FTM 73
4.4.3 Removing the Lower FTM 74
4.5 Installing a Fan Filter 75
Chapter 5 79
5.1 Overview 79
5.2 Network Management 79
ATCA Hub 82
Blade #1 82
Blade #n 82
# hpishaddr -b "07" 85
5.2.4 IP Addresses 86
SAM1410-1 87
SAM1410-2 87
5.2.4.1 Out-of-Band Interface 88
5.2.4.2 Backplane Interfaces 91
5.2.4.3 Configuration File 94
5.4 Software 100
5.4.2 Upgrade 101
5.5 Power Entry Module (PEM) 102
5.5.2 IPMC Circuitry 103
5.6 Fan Tray Modules 104
5.6.2 Cooling Budget 105
5.7 Redundancy 106
5.7.1.1 Heartbeat 107
5.7.1.2 Data Replication 107
5.7.1.3 HPI Interface 107
5.7.2.1 Shelf Manager 108
5.7.2.2 Hub Blade 109
5.7.2.3 System Manager 109
Figure 5-5 System Start-Up 110
5.7.3 Redundancy Operations 111
Supported IPMI Commands 119
6.2.3 Sensor Device Commands 120
6.2.4 FRU Device Commands 120
6.3 PICMG 3.0 Commands 121
Chapter 7 123
7.1 Introduction 123
7.2.2.1 Voltage Sensors 125
Table 7-4 Sensor No. 5 +3.3V 127
7.2.2.2 Temperature Sensors 129
7.2.2.3 Fan Speed Sensors 133
Table 7-14 Sensor No. 9 Fan 2 134
7.2.3.1 Hot Swap Sensor 143
7.2.3.2 IPMB Link Sensor 143
7.2.3.3 Reserved Sensor 144
7.2.3.4 OEM-Reserved Sensors 145
7.3.1 PEM FRU Information 152
7.3.2 E-Keying 153
7.3.3 Power Configuration 154
Voltage Sensors 155
Current Sensors 155
Temperature Sensor 155
7.3.5.1 Voltage Sensors 156
7.3.5.2 Current Sensors 161
7.3.5.3 Temperature Sensor 162
7.3.6.1 Hot Swap Sensor 163
7.3.6.2 IPMB Link Sensor 164
Table 7-51 Sensor No. 5, CB 1 165
Table 7-52 Sensor No. 6 CB 2 166
Table 7-53 Sensor No. 7 CB 3 167
Table 7-54 Sensor No. 8 CB 4 167
Table 7-55 Sensor No. 9 CB 5 168
Shelf Management Alarm Module 171
8.2 Features 172
8.4 Functional Description 176
8.4.3 Master-Only I 177
8.4.4 Shelf FRU SEEPROM 177
8.4.5 SAM LEDs 178
8.5 Management and Control 179
8.5.1.1 Voltage Sensors 180
8.5.1.3 Fan Speed and Control 180
8.5.2 Redundancy Control 183
8.5.2.2 HRI Protocol 184
8.5.2.3 Ethernet Signals 185
8.6 Telco Alarm Functionality 186
8.6.2 Telco Alarm LEDs 187
8.6.3 Telco Alarm Interface 187
8.7 Hot Swap Interface 188
8.8 Power 188
8.9 SAM Software 188
8.9.1 imls Utility 189
Related Documentation 191
A.2 Related Specifications 192
Safety Notes 193
Operation 195
Grounding 197
Connectors and Cabling 199
Expansion and FRU Exchange 200
Environment 203
Sicherheitshinweise 205
System Installation 206
Stecker und Verkabelung 211
Umweltschutz 215
, 180, 188 219

Commenti su questo manuale

Nessun commento

Emerson 1410 Manuale di Servizio Pagina 80

Commenti su questo manuale

Prodotti e manuali riguardandi Gateway/Controller Emerson 1410